Monster Fairings?

[Blacksmith]

Anybody with experience with these? Of the few flaws on my bike are a chip on top of the fairing right under the left clip on where I assume the original owner tied her down improperly and a couple small places on the lower right piece where they didnt put heat shield on the inside and the pipe melted a nickel sized spot in the gray mid fairing. Then yesterday my stupid arse dropped her pulling up to a gas pump and the front tire hit some gas or oil and slid, I was all but stopped but it scratched up the right side in a few places. Yes I know theres no real damage and nothing to effect ride ability but i'm a bit anal about that stuff. I know Suzuki parts are pretty high and I've read several good reviews on Monsters but do any of you have any experience good or bad?

 

[Mr Brown]

This is a matter for @jeffgordons24 to comment on. I think he used that company.

 

[Busa_Havens]

I've got a set of Gen 2 fairings from Amazon for cheap if you're interested. Bought them and decided not to use them.

 

[jeffgordons24]

Yes @Mr Brown is correct. To be honest In your case, you would be thrilled.
The quality, fit and the finish of them was spot on. I had not one fitment issue. Paint quality I would put on par with any respray you would get from a body shop, a few minor flaws here and there but all in all the paint was good enough to look great even at close up inspection.
The issue I had was the graphics were not 100% oem and for me the oem graphics I happened to love on my bike. If I were not so OCD. The fairings would have been perfect but I let it get to me and wound up going all OEM.
The shipping time takes long but If you already have fairings then you atleast can ride while you wait.
They will help you and do right for you I can tell you that. They tried and tried to produce what I wanted but I did also compensate their shipping and customization fees each time.

If you have a gen 2 I think you should purchase @mabupa oem fairings he had on his bike, they were in pretty mint shape and he is looking to sell not sure if your close Florida.

 

[Blacksmith]

Yes @Mr Brown is correct. To be honest In your case, you would be thrilled.
The quality, fit and the finish of them was spot on. I had not one fitment issue. Paint quality I would put on par with any respray you would get from a body shop, a few minor flaws here and there but all in all the paint was good enough to look great even at close up inspection.
The issue I had was the graphics were not 100% oem and for me the oem graphics I happened to love on my bike. If I were not so OCD. The fairings would have been perfect but I let it get to me and wound up going all OEM.
The shipping time takes long but If you already have fairings then you atleast can ride while you wait.
They will help you and do right for you I can tell you that. They tried and tried to produce what I wanted but I did also compensate their shipping and customization fees each time.

If you have a gen 2 I think you should purchase @mabupa oem fairings he had on his bike, they were in pretty mint shape and he is looking to sell not sure if your close Florida.

View attachment 1597837

View attachment 1597838

View attachment 1597839

View attachment 1597840

View attachment 1597841

View attachment 1597842

View attachment 1597843

View attachment 1597844

View attachment 1597845

View attachment 1597846

View attachment 1597847

View attachment 1597848

View attachment 1597849

View attachment 1597850

View attachment 1597851

View attachment 1597852

View attachment 1597853

Dude those are the ones you weren't happy with? I saw where they would put graphics under the clearcoat for you and ice been thinking about an outlining pinstripe around the kanji. Something kind of subtle but to make it pop just a bit.
Btw yeah i'm only 30 miles from the Fl line, 2.5 hours from Daytona but his bike is a lot lighter. Mine is black with dark gray mid fairings where his is two tone gray. Thanks for the point though, and the info on Monsters

 

[jeffgordons24]

Dude those are the ones you weren't happy with? I saw where they would put graphics under the clearcoat for you and ice been thinking about an outlining pinstripe around the kanji. Something kind of subtle but to make it pop just a bit.

Yea lol I have issues...I sold them to a forum member here who had a accident last year so he can get his bike back together.
Like I said to someone other than myself they are perfect I just can’t ever leave things along
Here are what is on the bike as of now.

 

[Blacksmith]

Brother you have one gorgeous bike

 

[jeffgordons24]

Brother you have one gorgeous bike

Thank you it is getting there, slowly but surely.