My tag light install, Lite'N Bolts

[Greenbean]

So I got those Lite'N Bolts off of ebay, like 22 shipped to the door. Decided to try it out. They are actually pretty neat little lights. Of course I only wanted to use one of them b/c of my tag bracket, also courtesy of ebay has one center hole right above the tag for a light.  I barely had to trim a little "V" in the top center of the tag. And after going out last night and then coming back in darkness to check the light. I am going to put a spacer type washer between the tag light and the tag itself. You'll see in the last picture it barely lights up anything.  but I wonder if that matters or not...

Yeah, Yeah, I know...  I have some an exhaust coming

...TBA...

<span style='color:green'>Just laying the removed parts out.

Light installed, you can see how tidy this is going to be.

I used the factory wiring of course, but had to remove the tail to do final install.

Double checking for correct wires, pos and neg, Yup black is neg...

She makes light

View from the inside, it's going to be clean.

Used butt conectors, then taped her all up after checking again for proper operation.

I love this tag bracket and light combo. You can't see the actual lighted bolt from the rear. It's tucked in under the tails brake light. I am very impressed with the set up as it only cost me @50 bucks with some elbow grease.

Money shot from rear.

Like I said before, I am going to space it a little more so it shines a little more light on the tag...Updated pics to follow the next few days.</span>

 

[busaville]

Nice ... but it needs to be a little brighter. Just my

 

[Greenbean]

Nice ... but it needs to be a little brighter.  Just my  

I smell what your steppin in, I'll post more pics after I get it spaced out to shine more light on the tag. I loosened it up last night about a quarter inch and it will look really good when I have it spaced.

 

[busaville]

 

[efiguero]

I was planning on doing the same thing, but was it really needed to take apart the tail? Was that a big pain?

 

[05BUSABLU]

i had a simular gig , then i thought it would be better to be bright and seen so i got a 3 led unit and dayum its crazy bright....hope it works for ya

 

[SpeedAdict]

I went the same route but I just use mine as the tag mounting bolts got 2 one on each side and it is plenty bright and matches the angle of the plate. I tried your way initialy and just couldn't get it to work correctly. Good luck bro.

 

[Greenbean]

I was planning on doing the same thing, but was it really needed to take apart the tail? Was that a big pain?

Not at all, It's easy when you know where all the clips and screws are.

 

[BigRod1300]

I grabbed a 3 LED set up from customdynamics. Small chrome strip that mounts over the top of the plate. Nice and bright....figured if I light up the tag, I may not get pulled over for where it is mounted.

 

[BigBSBusa]

I don't see a plate!

 

[Greenbean]

I don't see a plate!

With more pics for sure....

 

[dalynchmob4]

found this one on ebay... it has about 6 LEDs underneath the top lip of the bracket...

 

[rockadaous]

I don't see a plate!

i was thinking the same thing

I wanna see more plate pics *wink* *wink*

 

[efiguero]

Bought one today with a 3 led light for $24.99 and & 7.99 shipping off Ebay. Hopefully it is bright enough.

 

[High-Gain Busa]

When I moved my plate from the back to the side I moved the Bolt LEDs to the side. One is using the old reflector screw hole and I put one more next to it. The angle is such that they shine at the top and bottom of the plate very well and look kind of trick.

 

[BigRod1300]

I double checked mine..it has 6 led light the plate shown above. I got the one w/o the frame.

another tag pics. See its well hidden..expectialy if the WIFE is with me.

 

[Aquaman]

I dont see the bike!!!

 

[Greenbean]

I see a really big uh tire, yup that tire is NICE!

 

[BusaWizard]

Looks nice.