1397 on stk wheelebase ?

[C_Henry]

Just curious to see if this combo has ever been riden at tha track. If so, how was it set up ? Thanks !

 

[badboysbailagnt]

www.spazracing.com had one stock wheel base went 8.60's maybe 8.70's

 

[STUNNAH]

Good to see you posting...Although I haven't been on much lately myself...Is the track open in Huntsville???

 

[C_Henry]

Good to see you posting...Although I haven't been on much lately myself...Is the track open in Huntsville???

Yea, it's open Fri-Sun. Fri night is test&Tune. And Sun eve is T&T . There's even a Gambler's race for tha bikes on Fri nights put on by Ray Metzker. Check it out !

 

[C_Henry]

www.spazracing.com had one stock wheel base  went 8.60's maybe 8.70's

I wonder if there's any video of that running ? Thanks !

 

[ccs273]

I'm ridding a 1430 with stock wheel base, back raised 1 inch, with 1 tooth down in the front & 3 up in the rear, haven't taking it to the strip yet( just to play....I'm not really into drag racing) but I did take it on a road coarse in GA, Lots of Freaking power!!!!!!!!!!!!!!!!!!!! going to have it dyno'd tomorrow!!!!, should be over 210hp!

 

[STUNNAH]

Good I hope to make it down this year...

 

[C_Henry]

Found out today, no spun bearing !!!!

 

[nitrousjunkie]

Found out today, no spun bearing !!!!

Great news!

 

[BA BUSA]

Found out today, no spun bearing !!!!

Great news!

+1 always good to hear that

 

[fstbusa]

www.spazracing.com had one stock wheel base went 8.60's maybe 8.70's

.... I've seen both his bikes and atleast 1 on spray and they were only going 9.0s at best.

not sure whether they were 1397s or stock bore but they were not runnin 8s



<!--EDIT|fstbusa
Reason for Edit: None given...|1144756726 -->

 

[C_Henry]

www.spazracing.com had one stock wheel base  went 8.60's maybe 8.70's

.... I've seen both his bikes and atleast 1 on spray and they were only going 9.0s at best.

not sure whether they were 1397s or stock bore but they were not runnin 8s

Bet they were wheelie'n most of tha track

 

[CYCLEERIC]

quite a few 1397s around on the street . It's the combo I will probably go with and hope to see over 200HP at the rear wheel .

 

[00Busa]

I've been 8.90s on my stock wheelbase 1397 at Commerce,Ga. this year. I ususally run 9.00~9-teens but have at least 6 tickets with mid/high8.90s. A good 330 seems to be more important than a good 60ft bcause a lot of runs I wheelied too much after a real good 60ft (low 1.50s) . 5 of the tickets have 1.53 60ft and 1 has a 1.52
Same bike I ride to Bike Weekt@ Myrtle Beach for the last 4 years.



<!--EDIT|00Busa
Reason for Edit: None given...|1145617218 -->

 

[C_Henry]

What kind of 1/8mi times ?

 

[00Busa]

My best was a 5.79 but high 5.80s and low 5.90s were consistent. I was also using VP U-4. 126~127 mph and 128.02 that one time on the 5.79 run.

 

[C_Henry]

K, thanks !

 

[Professor]

My best was a 5.79 but high 5.80s and low 5.90s  were consistent. I was also using VP U-4.  126~127 mph and 128.02 that one time on the 5.79 run.

Are you finding the the U4 has about the same A/F as pump gas or are you have to change your fuel mapping to run it?

 

[upncoming]

www.spazracing.com had one stock wheel base  went 8.60's maybe 8.70's

No way...Let see the video. Maybe on spray. But not just a 1397 all motor.

 

[upncoming]

I'm ridding a 1430 with stock wheel base, back raised 1 inch, with 1 tooth down in the front & 3 up in the rear, haven't taking it to the strip yet( just to play....I'm not really into drag racing) but I did take it on a road coarse in GA, Lots of Freaking power!!!!!!!!!!!!!!!!!!!! going to have it dyno'd tomorrow!!!!, should be over 210hp!

I got 205hp out of a Bob Carpenter 1363cc, Your 1397cc should at least be making 220hp.