Look what I did to my Gauges

[quizesilver]

dear all

i have done up my gauge but my temp doesnt seem to be at the right position same goes for the rpm.

i already done the reset.

the rpm will start from 0rpm. but my pervious idling is 1.2k.

the temp on the 1st start is ok. but after i off and on, the temp show a high temp when the tempt is still cold.

Any advise on this?

Thanks

 

[quizesilver]

adding on to the above post.
*-*-*-*-*-*-*-*

hi all

i run into some prob.
was doing the led gauge mod.

but some how after the mod all 4 meter is not working correctly.

the fuel gauge, i remember i had abt half tank full but it shows abt 3/4 full.

the rpm gauge, pervious setting is abt 1.2k. but now it's idle at 0rpm. it did goes up on rev but how to resolve this.

the speedo unable to check as didnt ride it.

the temp sensor was showing at 1/4 mark (between the mid and the end) and i let it idle till fan on which suppose to be at half way mark, it didnt reach there. it juz stop at there.( fan was on, thus quite sure it is suppose to be at mid point)

now i am sad i dont know what is going on.

tried the reset, but nt sure if it is working correct.

follow the steps in the manual, all meter will go to zero mark but after starting and off and start. it is back to the pervious problem..

all advise are welcome.

Thanks!

 

[tampaboy813]

adding on to the above post.
*-*-*-*-*-*-*-*

hi all

i run into some prob.
was doing the led gauge mod.

but some how after the mod all 4 meter is not working correctly.

the fuel gauge, i remember i had abt half tank full but it shows abt 3/4 full.

the rpm gauge, pervious setting is abt 1.2k. but now it's idle at 0rpm. it did goes up on rev but how to resolve this.

the speedo unable to check as didnt ride it.

the temp sensor was showing at 1/4 mark (between the mid and the end) and i let it idle till fan on which suppose to be at half way mark, it didnt reach there. it juz stop at there.( fan was on, thus quite sure it is suppose to be at mid point)

now i am sad i dont know what is going on.

tried the reset, but nt sure if it is working correct.

follow the steps in the manual, all meter will go to zero mark but after starting and off and start. it is back to the pervious problem..

all advise are welcome.

Thanks!

i'm thinking you have to make sure there put back on @ the same spot that there taken off @...other wise there going to read wrong..I had the same thing on a car I was building back in H/S


I would have take a picture of them b4 taking them off...just my .02

-Paul

 

[quizesilver]

adding on to the above post.
*-*-*-*-*-*-*-*

hi all

i run into some prob.
was doing the led gauge mod.

but some how after the mod all 4 meter is not working correctly.

the fuel gauge, i remember i had abt half tank full but it shows abt 3/4 full.

the rpm gauge, pervious setting is abt 1.2k. but now it's idle at 0rpm. it did goes up on rev but how to resolve this.

the speedo unable to check as didnt ride it.

the temp sensor was showing at 1/4 mark (between the mid and the end) and i let it idle till fan on which suppose to be at half way mark, it didnt reach there. it juz stop at there.( fan was on, thus quite sure it is suppose to be at mid point)

now i am sad i dont know what is going on.

tried the reset, but nt sure if it is working correct.

follow the steps in the manual, all meter will go to zero mark but after starting and off and start. it is back to the pervious problem..

all advise are welcome.

Thanks!

i'm thinking you have to make sure there put back on @ the same spot that there taken off @...other wise there going to read wrong..I had the same thing on a car I was building back in H/S


I would have take a picture of them b4 taking them off...just my .02

-Paul

hmm
okie!
i think i know how to solve!

thanks alot

 

[99'busa]

 

[quizesilver]

done mine and my buddy busa!

nice!

2 more buddy to go.

 

[BlkDrgnZ28]

im in on this cause this is a cheap ass mod

 

[214 Busa]

where can i get the LEDs?