paul-ash@
Registered
ODB-2 Connector (Red)
- Thread starter ratwell
- Start date
paul-ash@
Registered
thanks for that at all sorted now it was the pair valve I caught the plug and disconnected it so it through FI light on the dash
LarryG
Registered
Looking good there ......
sgerry
Registered
That’s the one fail IMHO- having the digital speedo avail on the display would be more useful to me than lean angle and brake force.
Ked0607
Registered
Yes I am very interested in a digital speedo read out.
InfiniteReality
Registered
Same here, I'd much rather digital speedometer than what we see. To me it seems like they could have easily incorporated a large speedo on the current LCD layout
Ked0607
Registered
Atleast had it as an option in the menus. Maybe when they Crack the ecu there will be options we don't know about. I know alot of vehicles have secret menus...
Mo-gen3
Registered
Installed a full exhaust system and air filter and a battery had hill and F1 codes showing up and messing up the whole ride for me i tried reading codes with @smithabusa code reader and dealer switch shows C1782 and U0123 tried erasing the codes i couldn’t it says failure
Hayabusa Wannabe
Registered
Mo-gen3
Registered
Thanks
Dustin02
Registered
Check you wheelspeed sensors. Front and rear.
Mo-gen3
Registered
Did turn off the traction control and the bike has been doing ok so far other than the lights(Hill!&F1) nothing was showing
Dustin02
Registered
U0123
ECM "Diagnosis flow: [a]" (Page 10H-11)
ABS control unit/ HU "Diagnosis flow: [d]" (Page 10H-12)
ECM and ABS control unit/ HU "Diagnosis flow: [c]" (Page 10H-12)
Looking through the flowcharts, it seems you may have missed a connector or pinched some wires maybe... I'd check the connection at the IMU which is right there in front of the battery, and also the ABS unit.
Need to download the gen3 manual that is on here and take a look at it.
I can't find anything on code: C1782. Are you sure that is correct?
ECM "Diagnosis flow: [a]" (Page 10H-11)
ABS control unit/ HU "Diagnosis flow: [d]" (Page 10H-12)
ECM and ABS control unit/ HU "Diagnosis flow: [c]" (Page 10H-12)
Looking through the flowcharts, it seems you may have missed a connector or pinched some wires maybe... I'd check the connection at the IMU which is right there in front of the battery, and also the ABS unit.
Need to download the gen3 manual that is on here and take a look at it.
I can't find anything on code: C1782. Are you sure that is correct?
Mo-gen3
Registered
I wasn’t sure about the c code to be honest
Mo-gen3
Registered
Can you send the manual please?
Dustin02
Registered
Hopefully these links still work in this thread. I'm on my work computer, so I can't tell you if they do or don't.
www.hayabusa.org
PDF service manual for Gen 3 | Gen 3 Busa Information
Has anyone found the service manual for the 22+ busa in PDF? I hate paper manuals much rather have it up on a 55 inch monitor to read while I work.....
Mo-gen3
Registered
Did forgot to mention that i installed a lithium battery and when returned the original battery it was fine after thatHopefully these links still work in this thread. I'm on my work computer, so I can't tell you if they do or don't.
PDF service manual for Gen 3 | Gen 3 Busa Information
Has anyone found the service manual for the 22+ busa in PDF? I hate paper manuals much rather have it up on a 55 inch monitor to read while I work.....
Similar threads
