Starting to feel stupid

[Rojo]

Forrest Gump as a kid | Random Thoughts

www.hayabusa.org

 

[202mphbusa]

Packed up OEM head to send to Port Tech for a valve job
Port and Polish

nothing wrong with Rings
Valve Seal does not look damaged
seems to be seated.

Was going to send my HMP BIG head for repair but that will need a lot of work( a couple small cracks between the intake ports by seats)
and the head is too big (said no one ever) bike is LAZY down low

 

[Dnyce]

Port tech does good work

 

[202mphbusa]

Head finished up
Should ship out tomorrow

Really can not find anything wrong with #1 piston. Or rings

 

[bigoltool]

Head finished up
Should ship out tomorrow

Really can not find anything wrong with #1 piston. Or rings

So tough to go through stuff like this. How do the Cylinder Bores look?

 

[202mphbusa]

So tough to go through stuff like this. How do the Cylinder Bores look?

look like when I got it back from Rick Stetson perfect
no damaged rings

 

[202mphbusa]

Ported head back yesterday
Adult Beverage and a hour and a half
valve adjustment is now
nominal +-.001 on intake and exhaust

 

[202mphbusa]

Think I found something

Cleaning up my cylinder I slid #1 piston in its bore
Sliding it up and down it felt not smooth. Pulled all the rings. Slid smoothly
One ring on test another test
What I found was when I put the oil ring in
Check 2-4. Fine.
One with JUST the oil ring was not smooth
Grabbed a slightly used oil ring expander Feels perfect now
Looking at the expander I do not see any problem.

 

[bigoltool]

Are these new rings, or same ones you had in it previously?

 

[202mphbusa]

Rings have a hour in them. Brand new
Only swapped the #1. Oil control expander

 

[shade]

Same oem block? Any damage that was attempted to be repaired?

 

[202mphbusa]

Same oem block? Any damage that was attempted to be repaired?

No block was only honed
I measured the block and pistons myself down wo .0001 of a inch
I think the oil expander is a little narrower than the others, allowing the first scraper I install to go either fully or partially past the step that is supposed to hold it. Cocking the expander slightly, causing the second scraper not to slide all the way back to the step on the expander

I have another block and set of pistons I will play with to see if that is it, but right now I want to get this assembled and back in the bike

 

[Dnyce]

Here’s something to make u feel better-I finished wiring my fueltech yesterday, and on first start (yea it started, hell yea) in ten seconds of running it pushed the cam tensioner out bcuz it wasn’t tight, and broke the cam chain.

 

[sixpack577]

Here’s something to make u feel better-I finished wiring my fueltech yesterday, and on first start (yea it started, hell yea) in ten seconds of running it pushed the cam tensioner out bcuz it wasn’t tight, and broke the cam chain.

pistons hit valves?

 

[202mphbusa]

Here’s something to make u feel better-I finished wiring my fueltech yesterday, and on first start (yea it started, hell yea) in ten seconds of running it pushed the cam tensioner out bcuz it wasn’t tight, and broke the cam chain.

sorry but others misfortune Is not something I find solace in
I feel your pain man

 

[Dnyce]

I feel your pain man

That’s what I was getting at, I know what pain u dealing with lol

The intake valves look ok, I’m not taking all the turbo stuff off to check the exhaust, just gonna leak the motor and hope it’s all around 2%. already ordered a chain this morning. No chain pieces are in the motor tho, perfect break.

 

[202mphbusa]

Motor reassembled. Cams in. Degree wheel on. Mag base is at work so. Check cam timing tomorrow