NewRider Reacts: Wow! I don't know what's better...the bike, or this forum?
- Thread starter HayaWakened
- Start date
Nice bike! As for the levers touching the dash, is a common problem when installing certain bar riser and lever combos. My levers had to be adjusted up/down until I found the “sweet spot” to were they clear the dash by 1 or 2 mm. Looks to me like the brake and clutch levers don’t seem to be adjusted to the exact same position.
Southern California
So Cal - Fontana, CA 92335
jeffgordons24
Registered
I’m late to the welcome wagon!
Sorry guys.
Welcome aboard great to have you !
Sorry guys.
Welcome aboard great to have you !
Mr Brown
Registered
Fontucky! We have a couple of members in your neck of the woods. I visited last September myself.
These top plates are not primarily meant to be a bar riser, rather a means of lowering the front end by being able to raise the fork sliders thru the yokes . . consequently being called a 'lowering yoke'.
Here's the lowering yoke on Ali-Express . . .
Cheap enough to change colors every other day!
If I could get one for my Gen 1 ( I haven't seen any available for Gen 1 ) I'd be' in with a grin' !
Hey does anyone know if the Gen 2 and Gen 1 have the same spacing on the fork slider/ bolt pattern for the top plate??
https://www.aliexpress.com/item/Fro...lgo_pvid=d638a194-237d-45eb-8595-3f6570772230
Last edited:
Nice color! Nice levers too
Hi mate , the bike looks like a well looked after example , I bet you are going to have a lot of fun getting to know it . Be interested in hearing how you are liking it once you get some ride time , be sure to keep us posted !! Oh yeah , before I forget , welcome to the org bro !!
Toad
Toad
LycansGhost
Registered
Nice rig conrgats!
04LE
Registered
Do you know if the bike was modded before you bought it? I'd be curious if the bike had a full exhaust on it and is tuned for that and not a stock pipe setup. They look pretty clean for 10k miles on them and it seems odd that an otherwise stock bike would have the front end lowered. Just my thoughts.
jeffgordons24
Registered
I spent weeks shopping for one of these badboys because my bike is now lowered in the rear and the front is stock height it looks like a monster truck pulling a hole shot.
What I found is that not all of these top plates are created equal. The indexing and positioning of the bars can vary drastically. I finally decided between the Roaring Toys or the Ball Z one.
The Roaring Toys was a nice product and definitely would have served me well but I wound up going with the Ball Z because it uses the clamp bolt to secure the clip on like the factory. That I felt was a definate plus.
Also something to bear mind to is the key cylinder. Those in the pic above do not appear to have a key cylinder provision.
https://www.ballzmotorsports.com/Hayabusa-Black-Silver-3D-Triple-Tree-Package-p/z184.htm
Ball Z one Found here
https://store.schnitzracing.com/roaring-toyz-triple-clamp-suzuki-gsx1300r-hayabusa-99-19/
That is the Roaring Toys.
Sorry for the lapse in answering this question, and I have no answer, just suspicions. Yes, it seems to me weird to lower the front, but I started (less than a week ago) knowing nothing about these bikes. Why would one need to lower the front end of a bike like this? Did Suzuki make a design/engineering error and lowering the front corrects it? What would be the application for a lowered front end (as opposed to raising the bars, which I get)?
Regarding exhausts: according to the dealer, there were no exhausts on this bike when they bought it at auction in Arizona May 2018 (according to the VIN report). Those bolt-ons, they said, "were some 'Busa OEMs we had laying around". Which leads me to believe there was an aftermarket setup of some sort...naturally. Also naturally, there's some spare wire underneath the rear seat trunk, which I haven't traced yet, but immediately suspected a power commander...but if the ECU's been flashed (as I suspect it has, since the throttle mode switch is disabled) why would one need a power commander?
I'm too new and uneducated to have any opinion, just all these questions and suspicions.
Now, in regards that lowering yoke (or riser-looking thing) currently on my bike: following are some photos that show how the rise has complicated the brake/clutch lever clearance (and, as well, the brake/clutch fluid reservoirs; note the scuff marks where they hit the instrument cluster fairing on wheel lock). This thread reports that such a mod complication is not unusual for these bike. I've not yet attempted to adjust the rotational aspect of the levers in order to compensate, but am already thinking any adjustment would result in either ergonomic unpleasantness, or an increase in reservoir contact at the fairing. And finally, why does it appear as though the instrument cluster (fairings) are out of alignment? The answer to this question may require a full disassembly of that cluster.
Mr Brown
Registered
Lowering triple clamp allows sliding the fork tubes up for the risers. Or lowering the bike for drag racing purposes. Clearance issues, as you've discovered, are solved by trimming, or removal of the clamp. Pull the fairings apart and see if you can fix the alignment of the gauges, be patient and you won't hurt anything.
Nastee
Registered
Plate is tripple tree that replaces the OE one that is flat with no openings. Holes allow forks to move up into tree or further which lowers front height of bike for better handling or drag set up.
RedBull
Registered
