second set of injectors

[202mphbusa]

FWIW huge shout out to PFTuning for hooking me up

PFTuning.com – Engine Management and Data Solutions

pftuning.com

 

[202mphbusa]

got my ECU back and spent last night playing with 4 ID1000's and 4 OEM injectors
playing with sequential firing in test mode
I need to get a life

 

[michael parris heuberger]

got my ECU back and spent last night playing with 4 ID1000's and 4 OEM injectors
playing with sequential firing in test mode
I need to get a life

Hi. That is the best life by far.

 

[TonyM995]

The guy thinks there should be no problem setting my Megasquirt up to run two injectors a cylinder

SO........................... eventually I will have to pony up the cash to have Richard make me a LA plenum with secondaries
And tuning will start again

Scott Davis makes a more cost effective water/air plenum. And he has gone 260+ at Loring.

Pure Meth seems to be a PIA

That’s what I was thinking and it costs a lot to setup a fuel system that can deliver such a massive amount of fuel. But the cost may be the same or close to a water/air plenum and eliminate the weight of the intercooler.

 

[202mphbusa]

Scott Davis makes a more cost effective water/air plenum. And he has gone 260+ at Loring.


That’s what I was thinking and it costs a lot to setup a fuel system that can deliver such a massive amount of fuel. But the cost may be the same or close to a water/air plenum and eliminate the weight of the intercooler.

Scott should receive my plenum today

 

[michael parris heuberger]

Scott Davis makes a more cost effective water/air plenum. And he has gone 260+ at Loring.


That’s what I was thinking and it costs a lot to setup a fuel system that can deliver such a massive amount of fuel. But the cost may be the same or close to a water/air plenum and eliminate the weight of the intercooler.

Hi. My fuel system was a round $7,000.00 not cheep to try to go fast.

 

[202mphbusa]

FWIW even if I put HUGE injectors in and ran pure Meth I would never give up the intercooler

Scott D knows what to do, He is either
1 Adding secondaries and a hot side IAT bung
2 Adding secondaries and a hot side IAT bung and replacing the intercooler core
3 Building me a new Plenum with Secondaries

 

[TonyM995]

Why not? I wish you and other guys who have turbo experience would share their thoughts on the HTP kit.

 

[202mphbusa]

Why not? I wish you and other guys who have turbo experience would share their thoughts on the HTP kit.

I have not really looked at the HTP kit

I would not give up the intercooler because no matter how chilling Meth is L/A intercooler will still lower the starting point

 

[202mphbusa]

Does anyone know Of a model of Noid light that I can use to test my 8 sequential injector pulses?

 

[smithabusa]

I just use LEDs

 

[202mphbusa]

I just use LEDs

You are a smarter man then me

 

[smithabusa]

You are a smarter man then me

I just spend too much of my free time tinkering with this stuff

 

[202mphbusa]

I just spend too much of my free time tinkering with this stuff

SO I stopped on the way home and grabbed a set of Noid lights
Threw a OHM meter on my ID1000 12 ohms

All of the noid lights in the kit measure under 5 ohms
Safe or Not to use on my stand alone ?

 

[Busa Quick]

Buy some 10 ohm resistors and put one in series with each light. That'll give you 15 ohms each which should be safe compared to your injectors. Resistor kits from Amazon are really cheap.

 

[202mphbusa]

 

[smithabusa]

Very nice!

 

[sportbikeryder]

Hi. My fuel system was a round $7,000.00 not cheep to try to go fast.

What in the world makes up your fuel system to total $7k?

 

[202mphbusa]

What in the world makes up your fuel system to total $7k?

Plenum ~4k
Mechanical pump ~900
Fuel filters+ fittings ~400
8 injectors I dunno my ID1000's were like 600 and my secondaries were 600 also so 1200 there

 

[michael parris heuberger]

Plenum ~4k
Mechanical pump ~900
Fuel filters+ fittings ~400
8 injectors I dunno my ID1000's were like 600 and my secondaries were 600 also so 1200 there

Hi. The ID's 1050cc and the IS's 2600 were $2000.00, intercooled Plenum $3850.00 modify the plenum to fit the ID 2600's,2nd radiator for the plenum fitting and needed to fire the coils for VP M1 MAXX Race H2O ECU and S&R ignighter.